How to Solve "scan unit open or paper jam 2" Error message on Samsung printer CLX-2160

Solution 1:

• Open and close the front cover. The jammed paper is automatically ejected from the machine. 
• Gently pull the paper out of the output tray. If there is no jammed paper or if there is any resistance when you pull, stop and go to the next step. 
• Lift the scan unit. 
• Holding the inner cover open, carefully take the jammed paper out of the machine. 
• Lowering down the scan unit gently and slowly until it is completely closed. The inner cover will be closed automatically by the scan unit closed. Be careful not to pinch your fingers! If there is any resistance and the paper does not move when you pull or if you cannot see the paper under the scan unit, continue to the next step. 
• Open the rear cover. 
• If you see the jammed paper, pull it straight up. 
• Close the rear cover. 
• Printing automatically resumes. 

Solution 2:

• If there is no debris or other foreign object in a sensor, it could still be something to small for you to see. 
• Try blowing out all those areas with a can of compressed air. 

Solution 3:

• Make sure the sensors are not just "stuck" in the wrong position. Sensors are spring-loaded and so should pop back to the detent position when pushed the opposite direction with a small pencil or ice pick. 

Solution 4:

• Verify that the scan unit (or automatic document feeder) cover is completely closed. 

Solution 5:

• Replace or clean the rollers.
• If you are Facing more problems Call us +1-855-517-2433 Customer Care

Open Heat Error on samsung SCX-4521F printer how to fix

Solution 1:

• Open the back cover.
• There are two wire connector just near ribbon connector: this is thermistor.
• Verify and fix. 
• If you are Facing more problems Call us +1-855-517-2433 Customer Care

How to Solve "scan unit open or paper jam 2" Error message on Samsung printer CLX-3175

Solution 1:

• Open and close the front cover. The jammed paper is automatically ejected from the machine. 
• Gently pull the paper out of the output tray. If there is no jammed paper or if there is any resistance when you pull, stop and go to the next step. 
• Lift the scan unit. 
• Holding the inner cover open, carefully take the jammed paper out of the machine. 
• Lowering down the scan unit gently and slowly until it is completely closed. The inner cover will be closed automatically by the scan unit closed. Be careful not to pinch your fingers! If there is any resistance and the paper does not move when you pull or if you cannot see the paper under the scan unit, continue to the next step. 
• Open the rear cover. 
• If you see the jammed paper, pull it straight up. 
• Close the rear cover. 
• Printing automatically resumes. 

Solution 2:

• If there is no debris or other foreign object in a sensor, it could still be something to small for you to see. 
• Try blowing out all those areas with a can of compressed air. 

Solution 3:

• Make sure the sensors are not just "stuck" in the wrong position. Sensors are spring-loaded and so should pop back to the detent position when pushed the opposite direction with a small pencil or ice pick. 

Solution 4:

• Verify that the scan unit (or automatic document feeder) cover is completely closed. 

Solution 5:

• Replace or clean the rollers.
• If you are Facing more problems Call us +1-855-517-2433 Customer Care

How to solve "System Error Cycle Power" on Samsung printers

This concern these printers: SCX-4828FN, SCX-4826, CLX-3170, CLX-3175...

Solution 1:

• Verify the USB cable connection.
• Insert it in a new USB port.

Solution 2:

 It's a fuser problem.

• Power off the printer and wait 5 minutes.
• Power on.
• If the error persist, replace the fuser
• If you are Facing more problems Call us +1-855-517-2433 Customer Care

How to fix Samsung Printer Errors.

Samsung Scanning error:

This error message is essentially a hardware error. Due to poor quality of the cables, large data needed by the scanner cannot be transmitted. You can replace the USB cable and try again.

Paperjam error:

This happens when the paper is stuck in your Printer. Open up your printer and check for any jammed paper.
If you can’t see any, you need to check the sensor located beside the exit rollers. Maybe it has been knocked and is in the incorrect position, or is damaged. If nothing works, try replacing it with a new sensor.

Square prints issue:

Sometimes your Printermay print out squares instead of regular text.
It can happen if you are using Firefox or printing content from sites which do not recognize the font used in the text.
To fix this problem you will need to reinstall all relevant drivers. If this doesn’t help then visit the printers and faxes folder, select your printer and choose the properties. Choose the Advanced option in the dialog box and select the print processor. Choose a different mode of graphics and try testing a page for printing.

Missing print:

Sometimes, a portion of your page could be devoid of print. It can happen because of incorrect paper size configuration. Check the settings and try again.

Mediatray empty:

Sometimes even if the tray is loaded with paper you could be getting this error message on your Printer. Try updating the drivers by visiting the Samsung site. This should rectify issues.

Toner light still on:

After replacing the toner cartridge you might still find the toner light is switched on continually. You need to check the fuse located on the front side of the cartridge. You could try replacing this with a 50 mA one.

This error usually occurs in the Samsung SCX-4216F.

Error code: H2:

This error code indicates that there is a problem with the fuser warming up. Make sure all the cables are connected.

Error code: 24:

This error code indicates that there is too much data which is overloading the printer memory.

You can select the ‘continue’ button or try reducing the amount of print jobs. You could also try adding more memory to the printer (usually helpful for colour printers to speed them up).

Errorcode: 50:

This indicates a malfunction in the fuser. It means the fuser is not heating up. Try switching off your Samsung Laser Printer for around 15 minutes and then switch it on again. In case this does not solve the problem, it could indicate a fault in the fuser assembly or in the power supply.

Error code: 16:

This error code means that the toner is low. That means the distribution of the toner inside the cartridge is inadequate. You need to take out the cartridge and shake it back and front gently. If this does not work try replacing the cartridge. You could also try cleaning the contacts.